DE-OIL-IT INDUSTRIAL STRENGTH CONCENTRATE
TECHNICAL PRODUCT BULLETIN #SW-73
USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION
LISTING DATE: SEPTEMBER 29, 2021
“DE-OIL-IT INDUSTRIAL STRENGTH CONCENTRATE”
I. NAME, BRAND, OR TRADEMARK |
---|
DE-OIL-IT INDUSTRIAL STRENGTH CONCENTRATE Type of Product: Surface Washing Agent |
II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT |
---|
Greenworld Innovations Corp. 3813 Highgate Drive Valrico, FL 33594 Phone: (407) 574-3898 Fax: (813) 413-6073 E-mail: [email protected] Website: www.deoilit.com (Mr. Ron McCarthy, CEO, or Mr. Danny Schillaci, COO) |
III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS |
---|
Greenworld Innovations Corp. 3813 Highgate Drive Valrico, FL 33594 Phone: (407) 574-3898 Fax: (813) 413-6073 E-mail: [email protected] Website: www.deoilit.com (Mr. Ron McCarthy, CEO, or Mr. Danny Schillaci, COO) |
IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION |
---|
1. Flammability: Non-flammable. 2. Ventilation: No mechanical ventilation required; fresh air supply recommended for inside confined spaces. 3. Skin and eye contact; protective clothing; treatment in case of contact: May cause eye irritation, manufacturer recommends use of goggles during application. In case of eye contact, flush with plenty of water. After initial flushing, remove any contact lenses and continue flushing for at least 15 minutes. For skin contact, wash exposed skin with soap and water. If redness, itching or a burning sensation develops get medical attention. 4.a. Maximum storage temperature: 120°F continuous, 140°F up to 5 days. 4.b. Minimum storage temperature: 35°F. 4.c. Optimum storage temperature range: 40°F to 120°F. 4.d. Temperatures of phase separations and chemical changes: Stable; however, avoid freezing application solution (concentrated product diluted with water) to avoid possible separation. |
V. SHELF LIFE |
---|
The shelf life of unopened containers in unlimited. Containers should remain capped when not in use to prevent contamination or evaporation. Activated concentrate (i.e., product diluted with water) has unlimited shelf life if kept capped. |
VI. RECOMMENDED APPLICATION PROCEDURES |
---|
1. Application Method: Product is to be used in diluted form and works just as well with fresh or salt water. This product works well with all types of oils contaminating shorelines, beaches, and rocks. Dilute to 30:1 (this is the application solution comprised of 30 parts water and one part product), spray on surface areas, and allow to soak time for 15 minutes before rinsing with water. For stubborn oil cleanup, after soaking scrub with brush before rinsing. Spraying means using mechanical methods such as a pump that can deliver 30 psi or greater. Rinsing is best performed with a pressure washer if available. Prior to application, use booms to prevent the product and oil mixture from entering open water. Water run-off can be collected by a vacuum apparatus as surface tension of the treated oil is reduced making pick up efforts easier (should not stick to vacuuming). The product and oil mixture, along with containment materials, should be disposed of according to local, state, and federal regulations. 2. Concentration/Application Rate: The volume of an application solution for shoreline cleanup means adding water (30 parts) to product (one part) and is dependent on size of cleanup area. In general the calculation of application solution (water plus product) volume in gallons is (Length x Width)*(0.08) – scale is in feet. As an example, a boundary of contaminated shoreline measuring 50 feet x 12 feet, would be 600 square feet. Then 600 square feet * 0.08 = 48 gallons, at 30:1 dilution ratio this would be 1.5 gallons of product and 46.5 gallons of water. Water does not need to be filtered and can be salt or fresh. 3. Conditions for Use: Outside air temperature of 50°F to 125°F is optimal; otherwise, there is no specific restrictions outside this range other than avoid freezing of application solution. Water temperature for activating the application solution produces optimal performance between 95°F to 125°F; otherwise, there is no specific restrictions outside this range other than avoid freezing application solution. Water source for application solution can be fresh, or a non-potable source such as natural sources (i.e., lakes, ocean). Ambient water temperature at source of oil spill should be above 35°F. Do no freeze product, possible separation could occur. Manufacturer resting time of dilution application solution includes: • When creating a diluted application solution according to a selected dilution ratio, the combined solution of water and product needs to rest. • Resting time of 30 minutes to one hour stabilizing at ambient temperature to which you are to apply the application solution is optimal. |
VII. TOXICITY AND EFFECTIVENESS | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
a. Toxicity:
NA |
VIII. MICROBIOLOGICAL ANALYSIS |
---|
NA |
IX. PHYSICAL PROPERTIES AND COMPONENTS |
---|
1. Flash Point: >212ºF 2. Pour Point: 26ºF 3. Viscosity: 1.505 cst at 40ºC 4. Specific Gravity: 1.1959 at 60ºC 5. pH: 12.9 6. Surface Active Agents: Anionic and nonionic surfactants, proprietary. 7. Solvents: CONFIDENTIAL 8. Additives: CONFIDENTIAL 9. Solubility in Water: High solubility in water. |
X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS | ||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|