X4JH2000

TECHNICAL PRODUCT BULLETIN #SW-70
USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION
LISTING DATE: MARCH 05, 2019
"X4JH2000"

I. NAME, BRAND, OR TRADEMARK
X4JH2000 Type of Product: Surface Washing Agent

II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT
X4 Environmental Inc. 14702 Jersey Shore Drive Houston, TX 77047 Phone: (281) 846-6003 E-mail: [email protected] (TszFung Benlux Tam)

III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS
X4 Environmental Inc. 14702 Jersey Shore Drive Houston, TX 77047 Phone: (281) 846-6003 E-mail: [email protected] (TszFung Benlux Tam)

IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION
1. Flammability: Non-flammable 2. Ventilation: Recommend using a respirator in confined areas. 3. Skin and eye contact; protective covering; treatment in case of contact: Wear rubber gloves and eye protection. In case of eye contact, wash eyes thoroughly for 15 minutes including upper and lower lids; and seek medical attention. In case of skin contact, irritation is possible; wash with soap and water for 15 minutes. If irritation persists, seek medical attention. 4.a. Maximum storage temperature: 95°F 4.b. Minimum storage temperature: 32ºF 4.c. Optimum storage temperature range: 75°F 4.d. Temperatures of phase separations and chemical changes: No phase changes have been observed

IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION

1. Flammability: Non-flammable
2. Ventilation: Recommend using a respirator in confined areas.
3. Skin and eye contact; protective covering; treatment in case of contact: Wear rubber gloves and eye protection. In case of eye contact, wash eyes thoroughly for 15 minutes including upper and lower lids; and seek medical attention. In case of skin contact, irritation is possible; wash with soap and water for 15 minutes. If irritation persists, seek medical attention.
4.a. Maximum storage temperature: 95°F
4.b. Minimum storage temperature: 32ºF
4.c. Optimum storage temperature range: 75°F
4.d. Temperatures of phase separations and chemical changes: No phase changes have been observed

V. SHELF LIFE
One year in a sealed container; and six months for an opened container.

VI. RECOMMENDED APPLICATION PROCEDURE
1. Application Method: X4JH2000 is applied by spraying apparatus or mixing on or into media using excavator and 2-inch discharge hose, fire nozzle, or water pump; and water trucks. 2. Concentration/Application Rate: X4JH2000 is a water-based chemical. Use a ratio of 1 to 1.5 U.S. gallons of X4JH2000 to 10 parts water (i.e., tap, salt or fresh water) per cubic yard of contaminated media. 3. Conditions for Use: Ambient temperature should be above 50ºF. Water salinity and age of hydrocarbon pollutants are not a condition of use. Prior to application, use oil spill absorbent, boom and/or pad to prevent X4JH2000 from run off into ditches, creeks, and waterways. Place collected booms, pads, and absorbents in black 55-gallon poly-bags, use duct tape to seal, and then place bags in hazardous waste container for disposal. Collected containment materials should be disposed of according to local, state, and federal regulations.

VI. RECOMMENDED APPLICATION PROCEDURE

1. Application Method: X4JH2000 is applied by spraying apparatus or mixing on or into media using excavator and 2-inch discharge hose, fire nozzle, or water pump; and water trucks.
2. Concentration/Application Rate: X4JH2000 is a water-based chemical. Use a ratio of 1 to 1.5 U.S. gallons of X4JH2000 to 10 parts water (i.e., tap, salt or fresh water) per cubic yard of contaminated media.
3. Conditions for Use: Ambient temperature should be above 50ºF. Water salinity and age of hydrocarbon pollutants are not a condition of use. Prior to application, use oil spill absorbent, boom and/or pad to prevent X4JH2000 from run off into ditches, creeks, and waterways. Place collected booms, pads, and absorbents in black 55-gallon poly-bags, use duct tape to seal, and then place bags in hazardous waste container for disposal. Collected containment materials should be disposed of according to local, state, and federal regulations.

VII. TOXICITY AND EFFECTIVENESS

a. Toxicity:

Material Tested	Species	LC50 (ppm)
X4JH2000	Menidia beryllina Mysidopsis bahia	145.89 96-hr 40.26 48-hr
No. 2 Fuel Oil	Menidia beryllina Mysidopsis bahia	18.82 96-hr 1.49 48-hr
X4JH2000 & No. 2 Fuel Oil (1:10)	Menidia beryllina Mysidopsis bahia	18.59 96-hr 2.07 48-hr
Reference Toxicant (SLS)	Menidia beryllina Mysidopsis bahia	4.64 96-hr 8.42 48-hr

b. Effectiveness
NA

VIII. MICROBIOLOGICAL ANALYSIS
NA

IX. PHYSICAL PROPERTIES
1. Flash Point (ASTM D-56): >220ºF 2. Pour Point (ASTM D-57): +28ºF 3. Viscosity (ASTM D-445): 4.99cSt at 40ºC 4. Specific Gravity (ASTM D-1298): 1.06 at 60ºF 5. pH (ASTM D-1293): 4.69 6. Surface Active Agents: HS Code 340211 anionic organic surface-active agents 7. Solvents: Not applicable 8. Additives: Not applicable 9. Solubility in Water: Not applicable

X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS

Compound	Concentration (ppm)
Arsenic	<0.050
Cadmium	<0.025
Chromium	<0.050
Copper	<0.100
Lead	<0.050
Mercury	<0.010
Nickel	<0.050
Zinc	0.461
Cyanide	<0.025
Chlorinated Hydrocarbons	<1.000

X4JH2000

Emergency Response