Search Frequent Questions

Filter By:

Active filters:

Remove all filters

Displaying 1 - 15 of 75 results

  • Change of owner and RMP facility ID number

    If a facility is sold to a new owner, does it keep its' original RMP Facility ID number? Yes. The facility will keep the ID number assigned by EPA.

    • Last published:

  • Facility ID number and re-registering a facility

    If a facility deregisters, then reregisters, should the facility use the original RMP Facility ID or will it be assigned a new ID? The facility should use the original ID assigned by EPA.

    • Last published:

  • Resubmission of RMP for a facility that previously deregistered

    A covered facility deregisters its RMP because it no longer has more than a threshold quantity of a regulated substance in a covered process. If the facility becomes subject to the CAA §112(r) risk management program regulations at a later date and submits a new RMP, should the facility submit…

    • Last published:

  • RMP Records Maintained Onsite

    Pursuant to 40 CFR Part 68, Subpart G, the owner or operator of a stationary source subject to the risk management program regulations in Part 68 must develop and submit a risk management plan (RMP). Does the owner or operator have to maintain a written copy of the RMP on…

    • Last published:

  • Change of Ownership

    If a facility that is subject to the risk management program regulations in 40 CFR Part 68 is sold to another owner, is the facility required to make a correction or a full update of its risk management plan (RMP)? If there are no changes in the covered operations at…

    • Last published:

  • RMP*eSubmit preparer access

    How does a new Preparer get access to a Risk Management Plan (RMP) via RMP*eSubmit? First, the person must register with CDX. To register with CDX, go to https://cdx.epa.gov/ and complete the registration process for a Risk Management Plan “Preparer”. Once set up as a “Preparer”, the Certifying Official needs…

    • Last published:

  • How does the Safe Drinking Water Act limit lead in pipes, plumbing fittings, fixtures, faucets, solder and flux?

    Answer: Section 1417 of the Safe Drinking Water Act (SDWA) establishes the definition for “lead free” as a weighted average of 0.25% lead calculated across the wetted surfaces of a pipe, pipe fitting, plumbing fitting, and fixture and 0.2% lead for solder and flux. The Act also provides a methodology…

    • Last published:

  • Is exposure to lead contaminated drinking water from absorption through skin a health threat?

    Answer: Human skin does not absorb lead in water. For more information visit our website: https://www.epa.gov/ground-water-and-drinking-water/basic-information-about-lead-drinking-water . Question (23002-32377) Find a printable PDF copy of all frequent questions pertaining to lead .

    • Last published:

  • Are non-transient, non-community water systems (NTNCWSs) required to monitor for lead and copper?

    Answer: All community water systems (CWSs) and NTNCWSs must collect lead and copper tap samples. The frequency of the monitoring and number of samples to be collected and analyzed is based primarily on the number of people served and tap water monitoring results. For an outline of monitoring requirements (e.g…

    • Last published:

  • Is there anything else I can do beyond flushing my tap or buying bottled water?

    Answer: Yes, find “Important Steps You Can Take to Reduce Lead in Drinking Water” if you are concerned about lead in their drinking water. The list is not intended to be exhaustive or to imply that all actions equally reduce lead from drinking water. EPA recommends you also contact your…

    • Last published:

  • My neighbors got their water tested and found lead. Is my water safe?

    Answer: Lead usually gets into drinking water through contact with plumbing materials such as lead pipes or lead solder, or faucets, valves, and fixtures made of brass (brass contains some lead). Since each home has different plumbing pipes and materials, test results are likely to be different for each home…

    • Last published:

  • Can one still sell lead solder under the Lead Ban?

    Answer: Section 1417(a)(3) of the Safe Drinking Water Act (SDWA) prohibits the sale of solder and flux that is not lead-free unless the solder or flux bears a prominent label stating that it is illegal to use the solder or flux in the installation or repair of any plumbing providing…

    • Last published:

  • Why do water systems add phosphate to drinking water? What are the health effects of drinking water containing phosphates? 

    Answer: Public water systems (PWSs) commonly add phosphates to drinking water to prevent the release of metals in drinking water. Orthophosphate is most commonly used for lead and copper control. Polyphosphates sequester iron and manganese to prevent discolored water but are not effective to control lead and copper. Blended phosphates…

    • Last published:

  • How does EPA verify accuracy and completeness of RMPs?

    What does EPA plan to do to verify the accuracy and completeness of submitted Risk Management Plans (RMPs)? All RMPs received by EPA go through an electronic verification process that checks the submission for its completeness. This completeness check determines whether information has been provided for all of the required…

    • Last published:

  • What is the timeline for posting the responses? Will we receive an email with notification on the answers or shall I monitor the website for the posting?

    EPA will respond to the individual email 1 - 2 days after receipt and will post the questions and answers to the RFA website very soon thereafter.

    • Last published: