EPA RCRA ID: VAD000020115
On this page:
- Cleanup Status
- Facility Description
- Contaminants at this Facility
- Institutional/Engineer Controls
- Enforcement and Compliance
- Related Information
- Contacts for this Facility
Cleanup Status
Note: The Virginia Department of Environmental Quality (VDEQ) is the lead agency for managing cleanups at this facility.
A Corrective Action Determination of “Complete with Controls” was issued on May 11, 2010. The final remedy states that no further actions to clean up soil or groundwater are necessary, given current and reasonably anticipated future land use. However, the final remedy also requires the facility to maintain institutional and engineering controls because waste with hazardous substances will remain in four closed surface impoundments. On October 11, 2013, a fully executed Uniform Environmental Covenants Act (UECA) agreement was recorded in the Washington County, Virginia Circuit Court. This document perpetuates activity and use limitations of the property. Therefore, the requirements of the post closure care plan were determined to be satisfied and the 2011 Order was terminated on March 5, 2014. A long term inspection was conducted in July 2016, and found no outstanding issues with the maintenance of the final remedy.
On August 31, 2016, the VDEQ conducted a Long Term Stewardship assessment to assess whether the remedy was implemented and protective of human health and the environment.
Cleanup Background
The Sterling Casket facility is located in Abingdon, Washington County, Virginia, near the intersection of State Routes 704 and 879. The site comprises approximately 4.9 acres of land and is improved with a process building, paved parking lot, and landscaped areas. The site is bound to the north by Tri-Tube Industries, to the east by State Route 704, to the south by State Route 879, and to the west by open, undeveloped land.
The site has been owned and operated by Sterling Casket since 1963. Sterling Casket uses the site to manufacture casket hardware. On-site activities include molding, casting, electroplating, painting, and assembly of casket hardware parts. Although lead casting was performed in the past, only zinc casting is currently performed.
Sterling Casket currently performs nickel and cyanide-based (copper and bronze) plating. The process building houses a machine shop, a casket hardware molding room, a shipping warehouse, a painting room, a flammable chemical storage room, several hardware assembly areas, and an electroplating process area.
Several hazardous waste surface impoundments at the facility were closed with wastes in place on May 31, 1989. The DEQ and Sterling Casket entered into a CO for post-closure care of the closed impoundments on September 30, 1994. A Deed Notice is in place identifying the location of the hazardous waste surface impoundments closed with waste in place as a landfill.
By Letter of Commitment dated August 21, 2002, Sterling notified the United States Environmental Protection Agency (EPA) and DEQ of its willingness to participate in the EPA’s Facility Lead Program to address the necessary RCRA Corrective Action (CA) work at the facility. On September 9, 2004 the Groundwater and Human Health Environmental Indicators were given a “yes” determination by the DEQ.
In a March 19, 2009 letter the DEQ: 1) concurred that Sterling Casket had satisfied the recommend clean-up action in the area around the Sump, 2) accepted the Phase I RCRA Facility Investigation (RFI) Report, and 3) concurred that the information submitted by Sterling Casket to the DEQ meets the criteria and standards of the Corrective Action Facility Lead Program, 4) advised that future land use on the facility property will still be restricted to industrial use only, and 5) advised that groundwater sampling must continue for at least three additional events to confirm the levels of hazardous constituents in groundwater.
In October 2009, EPA and DEQ prepared a Statement of Basis (SB) and Administrative Record (AR) proposing a Final Remedy for Sterling Casket. The Final Remedy proposed is that no further actions to remediate soil, groundwater, or indoor air contamination are necessary to protect human health and the environment given current and reasonably anticipated future land use. The proposed final remedy would require Sterling Casket to develop and maintain certain property restrictions known as Institutional Controls (IC’s). The IC’s at Sterling Casket would be put in place to restrict use of the facility soil and groundwater to prevent human exposure to contaminants while contaminants remain in place. Sterling already has a Deed Notice with the Washington County Circuit Court Clerk’s Office, Deed Book 844, Page 767-768, identifying the location of the hazardous waste surface impoundments closed with waste in place as a landfill. The Deed Notice will be incorporated into the Declaration of Restrictive Covenants to ensure that the cap will not be disturbed.
These controls will provide assurance that the land use, as currently known and anticipated, does not change without additional investigation or work and prior notification to the EPA. EPA’s proposed decision represents “Corrective Action Complete with Controls” as described in EPA’s “Final Guidance on Completion of Corrective Action Activities at RCRA Facilities”, (68 FR 8757, February 25, 2003).
The Statement of Basis was public noticed in the Bristol Herald Courier on April 6, 2010. The public comment period lasted thirty (30) days ending on May 6, 2010. No comments were received during the public comment period therefore EPA issued a Corrective Action Determination of “Complete with Controls” on May 11, 2010.
Cleanup Actions or environmental indicators characterizing the entire facility are shown below. It is not intended as an extensive list of milestones/activities. This listing, and all the data on this page, come from EPA’s RCRAInfo and are refreshed nightly to this page. For this table and the Cleanup Activities Pertaining to a Portion of the Facility table that follows, a blank in the Status column could mean the action either has not occurred or has not been reported in RCRAInfo.
Cleanup Activities Pertaining to the Entire Facility
| Action | Status | Date of Action |
|---|---|---|
| Human Exposure Under Control Human Exposure Under Control(CA725) | ||
| Groundwater Migration Under ControlGroundwater Migration Under Control (CA750) | ||
| Remedy DecisionRemedy Decision (CA400) | ||
| Remedy ConstructionRemedy Construction (CA550) | ||
| Ready for Anticipated Use Ready for Anticipated Use (CA800) | ||
| Performance Standards AttainedPerformance Standards Attained (CA900) | ||
| Corrective Action Process TerminatedCorrective Action Process Terminated (CA999) |
For definitions of the terms used, hover over or click on the term.
Cleanup Activities Pertaining to a Portion of the Facility
| Action | Area Name | Date of Action |
|---|
For definitions of the terms used, hover over or click on the term.
Facility Description
Link to a larger, interactive view of the map.
The Sterling Casket facility is located in Abingdon, Washington County, Virginia, near the intersection of State Routes 704 and 879. The site comprises approximately 4.9 acres of land and is improved with a process building, paved parking lot, and landscaped areas. The site is bound to the north by Tri-Tube Industries, to the east by State Route 704, to the south by State Route 879, and to the west by open, undeveloped land. The site has been owned and operated by Sterling Casket since 1963. Sterling Casket uses the site to manufacture casket hardware. On-site activities include molding, casting, electroplating, painting, and assembly of casket hardware parts. Although lead casting was performed in the past, only zinc casting is currently performed.
Sterling Casket currently performs nickel and cyanide-based (copper and bronze) plating. The process building houses a machine shop, a casket hardware molding room, a shipping warehouse, a painting room, a flammable chemical storage room, several hardware assembly areas, and an electroplating process area.
Contaminants at this Facility
The primary contaminants of concern in the soil and groundwater were arsenic, cadmium, chromium, copper, lead, and, nickel.
Institutional and Engineering Controls at this Facility
Institutional Controls include:
- The cap on the hazardous waste surface impoundment area (landfill) shall not be disturbed.
- Groundwater will continued to be monitored for contaminants.
- No Construction shall take place at the facility without VDEQ/ EPA approval and residential dwellings/playgrounds are prohibited.
- All excavation of soil be done by trained personnel , tested for hazardous waste, and if found: disposed according to RCRA hazardous waste rules.
Institutional and Engineering Controls help ensure human exposure and groundwater migration are under control at a cleanup facility. Where control types have been reported by states and EPA in EPA’s RCRAInfo, they are shown below. Not all control types are needed at all facilities, and some facilities do not require any controls. Where there are blanks, the control types may not be needed, may not be in place, or may not be reported in RCRAInfo.
Are Controls in Place at this Facility?
|
Control(s) Type |
Control(s) in Place? |
Areas Subject to Control(s) |
Documents available on-line: |
|
|---|---|---|---|---|
|
Institutional ControlsNon-engineering controls used to restrict land use or land access in order to protect people and the environment from exposure to hazardous substances remaining in the site/or facility. (CA 772) |
Informational DevicesInformational Devices (ID) |
|||
|
Governmental Controls (GC) |
||||
|
Enforcement and Permit Tools (EP) |
||||
| Proprietary ControlsProprietary Controls (PR) | ||||
|
Engineering ControlsEngineering measures designed to minimize the potential for human exposure to contamination by either limiting direct contact with contaminated areas or controlling migration of contaminants. (CA 770) |
Groundwater ControlGroundwater Control (GW) |
|||
|
Non-Groundwater |
||||
For definitions of the terms used, hover over or click on the term.
Enforcement and Compliance at this Facility
EPA’s Office of Enforcement and Compliance Assurance (OECA) provides detailed historical information about enforcement and compliance activities at each RCRA Corrective Action Site in their Enforcement and Compliance Historical Online (ECHO) system.
RCRA Enforcement and Compliance Reports from ECHO
Related Information
For more information about this facility, see these other EPA links:
- RCRA information in EPA’s Envirofacts database
- Information about this facility submitted to EPA under different environmental programs as reported in EPA’s Facility Registry Services
- Alternative Names for this facility as reported by EPA programs in EPA’s Facility Registry Services
- Cleanups in My Community provides an interactive map to see EPA cleanups in context with additional data, and lists for downloading data
- Search RCRA Corrective Action Sites provides a search feature for Corrective Action Sites
Documents, Photos and Graphics
Contacts for this Facility
EPA Region implements and enforces the RCRA Corrective Action program for and federally recognized tribes.
For further information on this corrective action site, use the Contact Information for Corrective Action Hazardous Waste Clean Ups listings that are accessible through Corrective Action Programs around the Nation.